In some modems, the modem's radio can be ON when no SIM card is present.
In this case, the modem is in failed state, and the host cannot set the
power state to LOW. Since we we will allow the host to set the power to
LOW, we should allow it to set it back to ON.
These are thresholds for RSSI so nothing is expected to be
greater than 0.
This will allow to have a better granularity (even if with some
modem, we are limited in the number of thresholds configured)
These new thresholds will give the following signal quality range:
- 11% for -110 dBm
- 30% for -94 dBm
- 50% for -82 dBm
- 70% for -69 dBm
- 90% for -57 dBm
We are expecting to receive indication sreport every time the
signal strength crosses one of the configured thresholds.
Signed-off-by: Frederic Martinsons <frederic.martinsons@sigfox.com>
The timeout for sms send operation can exceed the current value, so
increase it to 5 minutes. Timeouts up to 4 minutes have been observed
in the following test scenario:
* Power up the modem and wait for registration.
* Right when the modem is registered, attenuate the rf signal
or remove the antenna.
* Immediately try to send an sms.
Increasing the timeout cover this corner case.
According to MBIM specification, the subscriber state is INITIALIZED
when SIM card is incompatible with enabled modem personalization lock.
This patch introduce additional check for enabled PIN lock in such case
and fixes depersonalization of one lock if several are enabled.
The suspend/resume option does not build properly if journal option
is disabled. This is beacause the journal option is check to add
suspend/resume code.
It has been fixed by replacing journal option check by the
suspend/resume option.
The process_get_all_call_info() was not completing the input GTask on
every possible code path (e.g. when remote party number or call info
wasn't available).
The method is now updated to avoid processing the GTask itself,
instead it will attempt to build the call list and return a GError on
any kind of failure.
Enable AT URCs for calls on top of QMI Voice indications
for AT+QMI devices only. Some AT+QMI devices send unreliable
QMI indications when the host is resuming. In such cases,
AT URCs can be used as a fall back to make calls reliable.
While AT+QMI devices relied before on AT commands to load
call list information and handle AT URCs for async updates,
this is now handled through QMI by forcefully reloading the
call list instead of processing the AT URCs.
This approach is disabled by default through the
MM_IFACE_MODEM_VOICE_INDICATION_CALL_LIST_RELOAD_ENABLED property.
This property is set to true in case of QMI modems.
meson is a build system focused on speed an ease of use, which
helps speeding up the software development. This patch adds meson
support along autotools.
The maximum MTU that the master interface can support should be less
or equal than RMNET_MAX_PACKET_SIZE, as defined in the
`rmnet_private.h` file in the linux sources (not a public header).
Only applicable to RMNET link management (i.e. not to qmi_wwan
add_mux/del_mux).
Fixes https://gitlab.freedesktop.org/mobile-broadband/libqmi/-/issues/71
When not requesting multiplexing support, only assume we don't need
any additional setup if multiplexing is disabled AND if the data modes
match between kernel and device.
This fixes the connection setup in MSM8916 (rpmsg+bam/dmux).
The new option will change the default setting in MBIM and QMI bearers
to "request" when no explicit "multiplex" configuration is given by
the user.
This option will help test the multiplexing support in the modems
before it's made a default in a future release.
The next 1.18 release will have multiplexing support, but not enabled
by default, to avoid breaking setups that don't expect the new virtual
net interfaces for the multiplexed sessions.
The exception is Qualcomm SoCs using the IPA driver, where
multiplexing is fully required.
The next 1.18 release will have multiplexing support, but not enabled
by default, to avoid breaking setups that don't expect the new virtual
net interfaces for the multiplexed sessions.
Using "requested" as a common default for every possible
implementation works, because it can handle setups without
multiplexing capabilities (e.g. plain AT+PPP modems) and also setups
without non-multiplexing capabilities (e.g. IPA based SoCs).
But if we don't want "requested" as default, then there will be
failing cases; e.g. we cannot use "none" as default for all as it
would break IPA, and we cannot use "required" as default for all as it
would break AT+PPP setups.
So, remove the common default, it's not flexible enough.
In IPA based setups, there are only multiplexed bearers supported,
there is no way to not enable multiplexing.
We change the logic that computes the maximum number of multiplexed
and non-multiplexed bearers, so that we check which are the current
kernel data modes before computing them.
Fixes warnings on AT+PPP based devices:
ModemManager[602870]: <debug> [1626948725.168355] [modem0] allowed up to 1 active bearers
(ModemManager:602870): GLib-GObject-WARNING **: 12:12:05.185: value "0" of type 'guint' is invalid or out of range for property 'max-active-multiplexed-bearers' of type 'guint'
A pointer can not be used anymore after its ownership has been transfered
using the g_steal_pointer function (pointer is nullified).
In this function, g_steal_pointer() is used when inserting 'value' inside
the array but can also be subsequently used when dumping 'value' to
'out_value' via g_strdup().
Fix that with simple reordering.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
The following functionalities are implemented:
1. Hold all and accept
2. Hangup all and accept
3. Hangup all
4. Join multiparty
5. Leave multiparty
6. Call transfer
Only the plural ATTRS form was checked but we also need to support
the single ATTR for matching device's attribute only.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
The template files in the `build-aux` directory used in enums sources
and headers generation use the `{$name}-template.[ch]` pattern.
However, the examples in the official guide[0] and usually GNOME and
Freedesktop packages use the `{$name}.[ch].template` pattern.
Due to this, the name of the template files and build commands have
been changed.
[0] https://developer.gnome.org/gobject/stable/glib-mkenums.html
Andrew Lassalle
Daniele Palmas
Amol Lad
Frederic Martinsons
Lubomir Rintel
Benoît Monin
Michal Mazur
Yegor Yefremov
Aleksander Morgado
Som_SP
Iñigo Martínez
Dylan Van Assche
ZhangMingjie
Loic Poulain
Joel Selvaraj
Teijo Kinnunen