Which reports the version of the currently active carrier
configuration.
We also update the firmware 'version' reported in the firmware
settings so that carrier-specific upgrades can be performed (e.g. when
the firmware stays the same but the MCFG is updated).
Ported from the broadband modem QMI implementation, keeping the logic
in place. We will need this to integrate mode/capability switching in
MBIM devices, for nothing else really (as MBIM already supports this
operation).
This commit introduces several improvements and changes in the way
modes and capabilities are managed in QMI capable devices. It is
organized into a single commit, as all changes in all 6 operations
(load current capabilities, load supported capabilities, set current
capabilities, load supported modes, load current modes, set current
modes) are related one to the other (given that the same QMI commands
are used for both capabilities and mode management).
The primary change is related to which capabilities are reported as
supported for a given device. In the previous implementation we
allowed switching between every combination possible for GSM/UMTS+LTE,
CDMA/EVDO+LTE or GSM/UMTS+CDMA/EVDO+LTE devices. E.g. we would allow
"LTE only" and "GSM/UMTS only" capabilities for GSM/UMTS+LTE devices,
even if they would both be managed in exactly the same way. That setup
wasn't ideal, because it meant that switching to a "LTE only"
configuration would require a power cycle, as capability switching
requires a power cycle, even if no change was expected in the exposed
DBus interfaces (which is why we require the power cycle). So, instead
of allowing every possible capability combination, we use capability
switching logic exclusively for configuring GSM/UMTS+CDMA/EVDO devices
(regardless of whether it has LTE or not) to add or remove the
GSM/UMTS and CDMA/EVDO capabilities. E.g. for a GSM/UMTS+CDMA/EVDO+LTE
device we would allow 3 combinatios: "GSM/UMTS+LTE", "CDMA/EVDO+LTE"
and "GSM/UMTS+CDMA/EVDO+LTE".
The "GSM/UMTS+CDMA/EVDO+LTE" is a special case because for this one we
allow switching to "LTE only" capabilities while we forbid switching
to "4G only" mode. As the same commands are used for mode and
capability switching, if we didn't have "LTE only" and we allowed "4G
only" mode instead and rebooted the device, we would end up not being
able to know which other capabilities (GSM/UMTS or CDMA/EVDO or both)
were also enabled.
Now that we have capability switching confined to a very subset of
combinations, we can use the mode switching logic to e.g. allow "4G
only" configurations in all non multimode devices, as well as masks of
allowed modes with one being preferred, which we didn't allow before.
In the previous implementation all mode switching logic was disabled
for LTE capable QMI devices. In the new implementation, we use the
"Acquisition Order Preference" TLV in NAS Set System Selection
Preference to define the full list of mode preferences for all
supported modes.
We also no longer just assume that NAS Technology Preference is always
available and NAS System Selection Preference only after NAS >= 1.1.
This logic is flawed, instead we're going to probe for those features
once when loading current capabilities, and we then just implement the
capabilities/mode switching logic based on that.
Devices will expect SUPL server given as either IP:PORT or FQDN:PORT,
so just avoid saying we require a 'URL' because it's not true.
We will use a new helper method to parse and validate user-provided
SUPL server address.
This patch fixes the following compiler warning:
mm-shared-qmi.c:447:9: error: implicitly declaring library function 'memset' with type 'void *(void *, int, unsigned long)' [-Werror,-Wimplicit-function-declaration]
memset (buf, 0, sizeof (buf));
^
Configuring reports every 5s may lead to GPGGA traces reported like this:
$GPGGA,211645.00,,,,,0,,,,,,,,*4D
$GPGGA,211646.00,4030.003988,N,00330.761876,W,1,07,1.0,691.6,M,53.0,M,,*74
$GPGGA,211650.00,,,,,0,,,,,,,,*49
$GPGGA,211651.00,4030.005405,N,00330.763540,W,1,07,1.0,688.9,M,53.0,M,,*71
$GPGGA,211655.00,,,,,0,,,,,,,,*4C
$GPGGA,211656.00,4030.008074,N,00330.765338,W,1,07,0.9,679.9,M,53.0,M,,*70
$GPGGA,211700.00,,,,,0,,,,,,,,*4D
$GPGGA,211701.00,4030.009258,N,00330.765510,W,1,07,1.0,678.3,M,53.0,M,,*71
$GPGGA,211705.00,,,,,0,,,,,,,,*48
Which is totally undesirable, as the GPS location would be flapping
between set and unset.
Use the default of 1s explicitly, which behaves properly.
The gpsOneXTRA assistance data provides a convenient way to inject
predicted orbit information into the module, without requiring to have
an Internet connection in the module itself.
This new interface will include implementations that are shared
between the MMBroadbandModemQmi and the MMBroadbandModemMbim.
For now, it just provides a way to implement the common client
allocation methods.
Aleksander Morgado
Ben Chan