On Huawei ME936, the hex numbers in the response to AT^DHCP contain the 0x prefix, e.g.
AT^DHCP?
^DHCP: 0xda7d0e0a,0xff000000,0xdb7d0e0a,0xdb7d0e0a,0x01261aac,0x00000000,100000000,50000000
This patch updates mm_huawei_parse_dhcp_response() to handle the
optional 0x prefix.
The generic broadband modem provides a common method to load unlock
retries based on CSIM queries. We modify the Telit plugin to use the
generic method but keeping the CSIM locking/unlocking logic in place.
The AT control TTYs in the u-blox modems may take some time to be
usable. In order to handle this issue, we configured some longer
timeouts during AT probing, but that may not be always enough.
The u-blox TTYs will report readiness via a "+AT: READY" URC, which
we can use during custom initialization to decide right away that the
port is AT. We use up to 20s as that is close to the worst case seen
during experimentation, happening after the module undergoes a full
NVM reset. If the timeout is reached without receiving the URC, we
still run standard AT probing afterwards. This new logic just tries
to make it sure we don't do any probing before the module is ready to
accept it.
If the module hasn't been hotplugged (i.e. it was already there when
ModemManager started) we do a quick first AT probing and if that fails
we run the "+AT: READY" URC wait as if it was hotplugged.
When in low-power mode, some modems will not dispatch unsolicited
notifications, such as for SIM hot swapping. There is code in
MMBroadbandModemTelit to handle this by checking the SIM identifier
during modem power up against the identifier cached in the SIM
D-Bus object. If they're different, the SIM has likely been
swapped while we were powered down.
We can move this code out to MMBroadbandModem because it doesn't
actually rely on any Telit-specific details, and invoke it from
MMIfaceModem via a new method.
The two connection and disconnection methods are ported to GTask, and
are also updated so that the reception of the unsolicited message
reporting either connect/disconnection is able to right away complete
the pending connection/disconnection attempts, as done in other
plugins like the Icera or HSO ones.
This block is a subclassed method from MMBaseBearer, which we just
happen to also use as part of the 3GPP dial logic in the connection
attempt.
So make it a separate logical block, and call the processing of the
connection attempt if one is found.
This change makes it similar to the same logic in the Icera plugin.
The Netgear AC341U seems to delay reporting packet service status
indications or actually not even send them. This leaves us with modems
in connected state in ModemManager but actually disconnected. We can
detect this situation by actively polling ourselves the connection
status.
See e.g. this case where the indication is received 2.5 mins after the
first OutOfCall error detected when loading statistics.
Aug 30 22:52:50 ModemManager[574]: <info> Modem /org/freedesktop/ModemManager1/Modem/0: state changed (connecting -> connected)
Aug 30 22:52:50 ModemManager[574]: <info> Simple connect state (8/8): All done
Aug 30 22:52:50 ModemManager[574]: <warn> Reloading stats failed: Couldn't get packet statistics: QMI protocol error (15): 'OutOfCall'
Aug 30 22:53:20 ModemManager[574]: <warn> Reloading stats failed: Couldn't get packet statistics: QMI protocol error (15): 'OutOfCall'
Aug 30 22:53:50 ModemManager[574]: <warn> Reloading stats failed: Couldn't get packet statistics: QMI protocol error (15): 'OutOfCall'
Aug 30 22:54:20 ModemManager[574]: <warn> Reloading stats failed: Couldn't get packet statistics: QMI protocol error (15): 'OutOfCall'
Aug 30 22:56:21 ModemManager[574]: <info> bearer call end reason (2): 'generic-client-end'
Aug 30 22:56:21 ModemManager[574]: <info> bearer verbose call end reason (3,2000): [cm] client-end
Aug 30 22:56:21 ModemManager[574]: <info> Modem /org/freedesktop/ModemManager1/Modem/0: state changed (connected -> registered)
The 'port' field in DetailedRegistrationStateContext is initialized to
NULL but never updated or used.
When detailed_registration_state_context_complete_and_free() calls
g_object_unref() on the NULL 'port' field, an assertion is raised.
This patch implements load_unlock_retries() for the Novatel LTE modem by
using the AT$NWPINR? command to query the number of retries left for
entering PIN1 or PIN2.
Ported from the original patch by Arman Uguray <armansito@chromium.org>:
https://chromium-review.googlesource.com/c/58118
Ben Chan
Ville Skyttä
Aleksander Morgado
Colin Helliwell
Eric Caruso