Make port roles more flexible. We have modems that do PPP
on interfaces other than the primary interface, and that
wasn't possible with the old code. So clean up all that
logic and move the port organization code into the core
so we can reduce code in the plugins.
In the new world order, the plugins say whether the port
is a QCDM port, an AT port, or ignored. If it's an AT
port the plugins get to tag it as primary, secondary, or
PPP, or any combination of the 3. This allows for modems
where PPP should really be done on the secondary port
(Huawei E220, Sierra devices) so that the primary port
stays open for command and status.
Modem subclasses no longer get asked to handle port grabbing
themselves. Instead, that's now done by the generic classes
(MMGenericCdma and MMGenericGsm) and the plugins are notified
when a port is grabbed so they can add unsolicited response
handlers for it. After all ports are grabbed by the generic
classes, they get "organized", which assigns various ports
to the roles of PRIMARY, SECONDARY, DATA, and QCDM based
on specific rules and hints that the plugin provided (which
are expressed as MMAtPortFlags). The plugins then have
a chance to perform fixups on the primary port if they choose.
The plugin code is responsible for determining the port
hints (ie MMAtPortFlags) at probe time, instead of having
a combination of the plugin and the modem class do the
job. This simplifies things greatly for the plugins at
the expense of more complicated logic in the core.
The property EnabledFacilityLocks on the .Modem.Gsm.Card interface
is a bit mask that indicates which of the various personalization
codes from 3GPP TS 22.022, plus the SIM PIN lock and SIM PIN2 lock,
are enabled. The set of facility locks supported by the modem is
determined at the time the modem is initialized, and the state of
each supported lock (enabled or disabled) is determined. When the
state of a lock changes, a property-change signal is sent out. Note
that ModemManager only supports enabling and disabling SIM-PIN, via
the EnablePin method on Modem.Gsm.Card.
Some modems only like the power-up command if not already in full functionality
mode. If the power-up is sent while already in full functionality mode, they get
rebooted and reseted.
With this changes, plugins can check whether they need the power-up and ask
the generic gsm code base to skip the command or not.
By default, power-up command (if any given) is never skipped.
Because the code was sending the USSD request with a "notify me via
unsolicited result code" tag, the response could come from any port,
and in was coming from other ports on various devices. But the code
expected the response on the main port, thus it got lost.
So turn the USSD response processing into an unsolicited command handler
instead, which allows us to process the response no matter where it
comes from. This patch also enables network-initiated USSD
notifications and requests since that's easy to add once the first thing
here is done.
We currently convert to and from the modem's set charset and always pass
'15' as the data coding scheme. Passing the correct data coding scheme
as third argument to CUSD only upsets the network. This contradicts 3GPP
TS 23.038. Other tools like gsm-ussd handle it the same way.
Network responses that require further actions are not yet implemented.
(some fixes and cleanups by Dan Williams)
An obfuscated SimIdentifier that may be available before the PIN has
been entered, for use in auto-unlocking a device. If this value is
present, it should be used in preference to DeviceIdentifier as it
is SIM-specific like the PIN code.
Pass the device's hardware IDs through modem creation and use them
when calculating the device's identifier. Add a bunch of testcases
for real hardware to ensure we don't break the device ID in the
future unless we really want to.
Some devices (Blackberries) always respond to AT+CREG with ERROR,
but will respond to AT+CGREG normally. Ugh. Handle that by
using the PS registration status from AT+CGREG if we don't have
a valid CS registration status at all.
Allow subclasses to override disconnect more cleanly so that
modem state gets handled correctly when the disconnect is complete.
Also fix up PDP Context ID handle (cid) so that subclasses can
get the previously-activated context ID when disconnecting, and let
the cid be an int since '0' is a valid context number.
For the generic devices, this also attempts to actually deactivate
the PDP context to ensure that the data session is terminated.
Instead of trying to stuff everything into the mode bitfield it
turns out it's just easier, clearer, and simpler to use different
values for each of the following:
1) the device's supported access technologies and allowed modes
2) the device's current access technology
3) the device's allowed mode preference
Since none of the AccessTechnology or AllowedMode stuff has hit a
release yet, let's make sure we're doing it the right way early on.
AccessTechnology takes over half of what NetworkMode was supposed to
do, but we'll keep NetworkMode around for a while for compatibility
anyway. Create async updaters that subclasses can use to update
the access tech when they get unsolicited messages.
First, generically handle registration polling if the device does
not support unsolicited registration. Second, using the new
creg/cgreg parsing functions from mm-modem-helpers.c, handle
CREG=2 unsolicited registration replies to capture the GSM LAC/CI
for the location information API.
Because of these changes we can simplify the registration polling
during connection as well by using the common registration parsing
code and the cached registration state.
For QCDM devices we want most of what MMSerialPort does, but not
the AT command handling stuff since the commands and responses
aren't AT commands nor are they even strings. So convert everything
that MMSerialPort does into a GByteArray, and let MMAtSerialPort
handle the conversion to strings when necessary.
Get rid of dependency on HAL, using libgudev instead. Fix up the plugin API
to no longer use either HAL or udev defines, but let plugins use whatever
mechanism they want for getting more information out of the device given the
subsystem and device node name.
Modems are now defined as "master" devices which "own" a one or more ports.
A port could be a serial tty device or a network device or whatever. The
plugin figures out whether it supports a given port or not and then assigns
it to a new or existing modem. Modems now have a 'valid' property that
should be set to TRUE when the modem has enough ports to operate correctly.
For devices (ex. 'hso') that use a network device for data transfer, the
modem would need to grab at least one TTY and the network device associated
with that physical device to be 'valid'.
Also move the generic modem support code to a plugin like other modem plugins,
and change the I-support-this-device mechanism to return a number indicating
the level of support. For example, the generic plugin would return a quite
low number if the device indicates via probing that it can do GSM or CDMA, but
a more specific plugin can indicate better support for the device, and thus
the more specific plugin would win control.
Implement registration using unsolicited messages for generic GSM class (which
is disabled by default, HSO and Huawei plugins enable it).
Modify all GSM modem subclasses that used unsolicited messages to use the new
method.
If the APN chosen by user is already configured in card, use that. If not,
find the highest used CID, the allowed range of CIDs and add new (or overwrite
the highest one).
Dan Williams
Aleksander Morgado
Eric Shienbrood
Guido Günther
Alexander Sack
Tambet Ingo