Rather than make all of them rely on MMBaseModem for it. This
lets us disentangle dependencies for easier unit testing.
For interfaces, rather than casting directly to MMBaseModem
use intermediate interfaces (MMIfaceAuth and MMIfaceOpLock)
that tests can fake out.
Signed-off-by: Dan Williams <dan@ioncontrol.co>
If a request to lock the operation with the override type arrives, all
pending operations will be immediately cancelled, and no new lock
requests will be allowed.
There are certain operations that cannot be run in parallel, e.g. one
should not disable and bring the modem to low power mode while there
are also incoming requests to enable the modem. This type of errors
will typically happen when multiple DBus clients are trying to use the
same modem at the same time for different purposes.
We do not have any way to have DBus clients take exclusive ownership
of a given modem object, so the best we can do for now is trying to
synchronize operations that cannot be run together, preserving the
order in which they arrived, and running them one by one.
No users left for the getter that takes a reference after a port of
MMBaseModemAT to GTask.
peek_cancellable() is used instead, because the GTask constructor
takes a reference itself.
We no longer have separate mm_base_modem_process_sim_event() and
mm_broadband_modem_sim_hot_swap_detected() methods. The only
difference between both of them was that one of them would attempt to
cleanup the ports context associated to the SIM hot swap event logic
as soon as a swap was detected, in order to avoid queueing up multiple
such events.
The previous logic wasn't working well, though, as there could be
mixed AT+QMI or AT+MBIM devices that would also require that same
cleanup and so we didn't always know which one should have been
called.
Now we have a single mm_iface_modem_process_sim_event() method, which
will trigger the reprobe and disabling, but which will also perform
the cleanup of the SIM ports swap setup as specified by the
implementation.
So, if a plugin explicitly initializes the serial ports context for
SIM hot swap handling, it should also explicitly clean it up.
Also, the initialization of the serial ports context for SIM hot swap
handling is no longer done automatically for all modems, it will be
done only for those modems using it; i.e. the modems that explicitly
report support SIM hot swap handling using AT URCs.
When new link ports are created, the QmiDevice link management methods
try to make sure that the port exists in the system by the time the
link addition method returns, but that doesn't guarantee that the port
has also been notified by the kernel to ModemManager (e.g. via udev or
via kernel events).
This new method allows to do a explicit wait for a given port link; if
we already have it it will return right away, and otherwise we'll wait
for it to be notified via the "link port grabbed" signal.
We will grab the ports and make them available through find_ports() or
peek_port() or get_port().
The link ports are not 'organized' so they won't be available in
e.g. get_data_ports(), which is fine, because we don't want to mix
them with the real data ports exposed by the device.
Link port additions and removals are also notified via signals in the
modem object, so that explicit wait for specific ports can be done.
Right now just with the support to setup link properties like up/down
state or the link mtu.
This features are required when using QMAP based multiplexing with the
qmi_wwan kernel driver.
If the lock status cannot be read during a puk unblock attempt, reprobe
the modem. It is likely that the SIM was permanently blocked if the lock
status cannot be read.
When the SIM switch doesn't happen as part of an async hot swap
detection, we should trigger the switch handling at base modem level,
which e.g. doesn't require explicit cleanup of the SIM hot swap
detection port context.
The auth provider setup is a bit over-engineered. Simplify it by
making a single MMAuthProvider object that may or may not use polkit,
depending on configure options. This object is also setup as a
singleton object using the helper MM_DEFINE_SINGLETON_GETTER().
Instead of flagging them as 'ignored' so that they aren't probed, we
can also flag them as 'audio' now, so that the logic knows which port
to report as used for audio in the Call object.
The mm_base_modem_grab_port() now receives a MMKernelDevice directly from the
plugin, which is then stored in the MMPort corresponding to the port.
This means that we have direct access to e.g. all properties set by udev rules
everywhere, and we don't need additional GUdevClient objects (e.g. like the one
used in the Huawei plugin to detect NDISDUP support during runtime).
For virtual ports (e.g. generated during unit tests), we have a new 'generic'
kernel device object which just provides the values from the kernel device
properties given during its creation.
BaseModem
added reprobe property.
MMDevice
added logic to recreate the modem if it is set invalid and "to reprobe"
MMBroadbandModem
* added initialization step for SIM hot swap:
1. keep dedicated ports open to listen to modem's unsolicited
2. dedicated error management in case of initialization failure due to SIM missing
* added function to be called in order to act upon SIM insertion/removal:
1. close dedicated ports
2. set the modem to be reprobed
3. disable modem
* added SIM HOT SWAP boolean property
MMIfaceModem
* added initialization step for SIM hot swap, if supported by the plugin
* dedicated error management in case of initialization failure due to SIM missing
We will expose a new 'Ports' property listing all ports currently known by a
given modem. Ports which are not used but are detected as being part of the
modem will be listed with an 'unknown' port type.
This change uses the new 'MMModemPortType' enum and the new 'MMModemPortInfo'
helper struct to handle these values in libmm-glib. The already available
'MMPortType' enum hasn't been re-used for the interface because it contains
values that we don't need (e.g. IGNORED).
The port list is now also included in the modem information command of mmcli:
$ sudo mmcli -m 0
/org/freedesktop/ModemManager1/Modem/0 (device id '97b7b99e3e2bea103880545b619fb05a3cc81b26')
-------------------------
System | device: '/sys/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.4'
| drivers: 'qcserial, qmi_wwan'
| plugin: 'Gobi'
| primary port: 'cdc-wdm0'
| ports: 'ttyUSB0 (qcdm), ttyUSB1 (at), cdc-wdm0 (qmi), wwp0s29u1u4 (net)'
https://bugzilla.gnome.org/show_bug.cgi?id=702678
Instead of deciding in advance which data port to use, we let the dialling
operation gather it. For the generic dialling logic, ATD-based, always an
'AT' port will be used as data port, even if we grabbed a 'net' port. Those
plugins that can work with 'net' ports will grab the specific 'net' port
themselves.
Dan Williams
Lukas Voegl
Sushrut Shree Trivedi
Aleksander Morgado
Lubomir Rintel
Rukun Mao
Daniele Palmas
Aleksander Morgado
Dylan Van Assche
Pavan Holla
Matthew Stanger
Carlo Lobrano
Aleksander Morgado