This allows using it with CLEANUP_ARRAY(). For the 2 call sites
where we don't need to free the array, we do a regular for loop
calling json_variant_unref() instead.
We have this very similar code in various places, and it#s not entirely
obvious (since we want a prolonged timeout for the reload), hence unify
this at one place.
When this option is set to direct, the service restarts without entering a failed
state. Dependent units are not notified of transitory failure.
This is useful for the following use case:
We have a target with Requires=my-service, After=my-service.
my-service.service is a oneshot service and has Restart=on-failure in
its definition.
my-service.service can get stuck for various reasons and time out, in
which case it is restarted. Currently, when it fails the first time, the
target fails, even though my-service is restarted.
The behavior we're looking for is that until my-service is not restarted
anymore, the target stays pending waiting for my-service.service to
start successfully or fail without being restarted anymore.
The article "a" goes before consonant sounds and "an" goes before vowel
sounds. This commit changes an to a for UKI, UDP, UTF-8, URL, UUID, U-Label, UI
and USB, since they start with the sound /ˌjuː/.
quality_check_password() used to return the same value 0 in two
different cases: when pwq_allocate_context() failed with a
ERRNO_IS_NOT_SUPPORTED() code, and when pwquality_check() rejected the
password. As result, users of quality_check_password() used to report
password weakness also in case when the underlying library was not
available.
Fix this by changing quality_check_password() to forward the
ERRNO_IS_NOT_SUPPORTED() code to its callers, and change the callers
to handle this case gracefully.
Add function to simplify getting the TPM SRK; if one exists, it is provided,
otherwise one is created and then the new SRK provided.
This also add tpm2_create_loaded() and updates tpm2_seal() to use the new
functions instead of tpm2_make_primary().
Let's add two new helpers: mount_credentials_fs() and
credentials_fs_mount_flags(). The former mounts a file system suitable
for storing of unencrypted credentials at runtime (i.e. a ramfs or
tmpfs). The latter determines the right mount flags to use for such a
mount.
Both functions mostly just take code from execute.c, but make two
changes:
1. If the kernel supports it we'll use a tmpfs with the new "noswap"
mount option instead of ramfs. Was added in kernel 6.4, hence is very
recent, but tmpfs is so much less crappy than ramfs, hence worth it.
2. We'll set MS_NOSYMFOLLOW on the mounts if supported. These file
systems should only contain regulra files, hence no need to allow
symlinks.
Let's hook up one more thing with credentials: the machine ID to use
when none is initialized yet.
This requires some reordering of initialization steps in PID 1: we need
to import credentials first, and only then initialize the machine ID.
This is just like read_credential() but also looks into the encrypted
credential directory, not just the regular one.
Normally, we decrypt credentials at the moment we pass them to services.
From service PoV all credentials are hence decrypted credentials.
However, when we want to access credentials in a generator this logic
does not apply: here we have the regular and the encrypted credentials
directory. So far we didn't attempt to make use of credentials in
generators hence.
Let's address and add helper that looks into both directories, and talks
to the TPM if necessary to decrypt the credentials.
When the credential dir is backed by an fs that supports ACLs we must be
more careful with adjusting the 'x' bit of the directory, as any chmod()
call on the dir will reset the mask entry of the ACL entirely which we
don't want. Hence, do a manual set of ACL changes, that only add/drop
the 'x' bit but otherwise leave the ACL as it is.
This matters if we use tmpfs rather than ramfs to store credentials.
Certain cards support to set their eswitch to switchdev mode. In this
mode for each created VF there is also created so called VF representor.
This representor is helper network interface used for configuration of
mentioned eswitch and belongs to an appropriate PF.
VF representors are identified by the specific value of phys_port_name
attribute and the value has format "pfMvfN" where M is PF function
number and N is VF number inside this PF.
As the VF representor interfaces belong to PF PCI device the naming
scheme used for them is the same like for other PCI devices. In this
case name of PF interface is used and phys_port_name suffix is appended.
E.g.
PF=enp65s0f0np0 # phys_port_name for PF interface is 'p0'
VF=enp65s0f0np0v0 # v0 is appended for VF0 in case of NAMING_SR_IOV_V
REP=enp65s0f0np0pf0vf0 # phys_port_name for VF0 representor is 'pf0vf0'
First as the phys_port_name for representors is long (6+ chars) then the
generated name does not fit into IFNAMSIZ so this name is used only as
alternate interface name and for the primary one is used generic one
like eth<N>. Second 'f0' and 'pf0' in REP name is redundant.
This patch fixes this issue by introducing another naming scheme for VF
representors and appending 'rN' suffix to PF interface name for them.
N is VF number so the name used for representor interface is similar to
VF interface and differs only by the suffix.
For the example above we get:
PF=enp65s0f0np0
VF=enp65s0f0np0v0
REP=enp65s0f0np0r0
This eases for userspace to determine which representor interface
represents particular VF.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Daan De Meyer
Lennart Poettering
Yu Watanabe
Mike Yuan
Xeonacid
Luca Boccassi
Richard Phibel
Daniel P. Berrangé
Egor IgnatovandDmitry V. Levin
Joerg Behrmann
Dmitry V. Levin
Antonio Alvarez Feijoo
Dan Streetman
Zbigniew Jędrzejewski-Szmek
Ivan Vecera