The following bond options are supported by this patch.
MIIMonitorSec:
Specifies the frequency in milli-seconds that MII link
monitoring will occur.
UpDelaySec:
Specifies the delay time in milli-seconds to enable a link
after a link up status has been detected.
DownDelaySec:
Specifies the delay time in milli-seconds to disable a link
after a link failure has been detected.
changes:
1. Added gconf variables.
2. man page
conf:
[NetDev]
Name=bond1
Kind=bond
[Bond]
Mode=802.3ad
TransmitHashPolicy=layer2+3
LacpduTransmitRate=fast
MIIMonitorSec=1s
UpDelaySec=2s
DownDelaySec=8s
cat /proc/net/bonding/bond1
Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
Bonding Mode: IEEE 802.3ad Dynamic link aggregation
Transmit Hash Policy: layer2+3 (2)
MII Status: up
MII Polling Interval (ms): 1000
Up Delay (ms): 2000
Down Delay (ms): 8000
802.3ad info
LACP rate: fast
Min links: 0
Aggregator selection policy (ad_select): stable
bond bond1 has no active aggregator
[tomegun: rephrased manpage, dropped bond_ prefix from variables]
LacpduTransmitRate
option specifies the rate in which link partner to transmit
LACPDU packets in 802.3ad mode. Possible values
slow : Request partner to transmit LACPDUs every 30 seconds
fast : Request partner to transmit LACPDUs every 1 second
The default is slow.
chages:
1. Added enum bond_lacp_rate_table
2. gperf LacpduTransmitRate
Test:
conf file:
[NetDev]
Name=bond1
Kind=bond
[Bond]
Mode=802.3ad
LacpduTransmitRate=fast
test:
cat /proc/net/bonding/bond1
Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
Bonding Mode: IEEE 802.3ad Dynamic link aggregation
Transmit Hash Policy: layer2+3 (2)
MII Status: up
MII Polling Interval (ms): 0
Up Delay (ms): 0
Down Delay (ms): 0
802.3ad info
LACP rate: fast
Min links: 0
Aggregator selection policy (ad_select): stable
bond bond1 has no active aggregator
[tomegun: renamed from LacpduTransmitRate to LACPTransmitRate, manpage fixes and
dropped bond_ prefix from variables]
This patch adds support the transmit hash policy to use
for slave selection in balance-xor, 802.3ad, and tlb modes
layer2, layer3+4, layer2+3, encap3+4, encap3+4
Added:
1. BondXmitHashPolicy
2. conf param TransmitHashPolicy
Test conf:
[NetDev]
Name=bond1
Kind=bond
[Bond]
Mode=802.3ad
TransmitHashPolicy=layer2+3
test output:
cat /proc/net/bonding/bond1
Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
Bonding Mode: IEEE 802.3ad Dynamic link aggregation
Transmit Hash Policy: layer2+3 (2)
MII Status: up
MII Polling Interval (ms): 0
Up Delay (ms): 0
Down Delay (ms): 0
802.3ad info
LACP rate: slow
Min links: 0
Aggregator selection policy (ad_select): stable
bond bond1 has no active aggregator
[tomegun: dropped bond_ prefix from new Bond variable, drop repeated man-page section]
This patch adds supports networkd to configure bond mode
during creation via persistent conf. Mode can be configured
with conf param 'Mode'. A new section Bond is added to the
conf to support bond mode.
These modes can be configured now.
balance-rr
active-backup
balance-xor
broadcast
802.3ad
balance-tlb
balance-alb
Example conf file: test-bond.conf
[NetDev]
Name=bond1
Kind=bond
[Bond]
Mode=balance-xor
Test case:
1. start networkd service:
12: bond1: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc
noqueue state UNKNOWN mode DEFAULT group default
link/ether 22:89:6c:47:23:d2 brd ff:ff:ff:ff:ff:ff
2. find bond mode:
cat /proc/net/bonding/bond1
Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
Bonding Mode: load balancing (xor)
Transmit Hash Policy: layer2 (0)
MII Status: up
MII Polling Interval (ms): 0
Up Delay (ms): 0
Down Delay (ms): 0
Changes:
1. Added file networkd-bond.c
2. Bond mode enum BondMode
3. conf section [Bond]
[tomegun: whitespace]
This patch introduces TUN/TAP device creation support
to networkd.
Example conf to create a tap device:
file: tap.netdev
------------------
[NetDev]
Name=tap-test
Kind=tap
[Tap]
OneQueue=true
MultiQueue=true
PacketInfo=true
User=sus
Group=sus
------------------
Test:
1. output of ip link
tap-test: tap pi one_queue UNKNOWN_FLAGS:900 user 1000 group 1000
id:
uid=1000(sus) gid=10(wheel) groups=10(wheel),1000(sus)
context=unconfined_u:unconfined_r:unconfined_t:s0-s0:c0.c1023
Modifications:
Added:
1. file networkd-tuntap.c
3. netdev kind NETDEV_KIND_TUN and NETDEV_KIND_TAP
2. Tun and Tap Sections and config params to parse
conf and gperf conf parameters
[tomegun: tweak the 'kind' checking for received ifindex]
It may sometimes be necessary to specify the MAC address of a netdev.
Let us set the correct one from the get-go, rather than having the
kernel generate a random one, and then change it after.
This patch adds path of mtu discovery for sit tunnel.
To enable/disable DiscoverPathMTU is introduced.
Example configuration
file: sit.netdev
[NetDev]
Name=sit-tun
Kind=sit
MTUBytes=1480
[Tunnel]
DiscoverPathMTU=1
Local=X.X.X.X
Remote=X.X.X.X
By default pmtudisc is turned on , if DiscoverPathMTU
is missing from the config. To turn it off
DiscoverPathMTU=0 needs to be set.
This does not belong in shared as it is mostly a detail of our networking subsystem.
Moreover, now we can use libudev here, which will simplify things.
Susant Sahani
Tom Gundersen