Add some mmcli D-Bus timeout slack, making them slightly higher than the
ModemManager internal timeout, to ensure the cli doesn't time out the
D-Bus call when MM succeeds.
For 3GPP scan, some modems appear to have internal 5 minute timeouts,
so ensure MM doesn't time out right before the modem returns results:
ModemManager[282578]: <dbg> [1741054422.321400] [ttyUSB2/at] --> 'AT+COPS=?<CR>'
ModemManager[282578]: <wrn> [1741054722.247806] [modem1] failed scanning networks: Serial command timed out
ModemManager[282578]: <dbg> [1741054724.119770] [ttyUSB2/at] <-- '<CR><LF>+COPS: (1,"T-Mobile","T-Mobile","310260",0),,(0,1,2,3,4),(0,1,2)<CR><LF><CR><LF>OK<CR><LF>'
Signed-off-by: Dan Williams <dan@ioncontrol.co>
For a ModemManager simple connect using mmcli, added the bearer
path on which call is connected. This helps in determining the
bearer path to directly retrieve bearer information easily
of this particular call.
Signed-off-by: Anagh G <quic_anaghg@quicinc.com>
Instead of relying on getting/setting the UE mode via AT +CEMODE command
which on Quectel RM520N (And I assume other QMI based modems) only allows
getting the value and not setting one it has special AT commands for CS/PS
and voice/data centric values.
So lets instead use the QMI Get/Set System Selection Preference TLV which
offers service domain and usage domain preference info so we can use those
to get/set the 3GPP TS 24.301 UE mode values.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
According to 3GPP Rel17.2, TS 38104, band NGRAN-67 is supported.
Currently Qualcomm SDX72 chip support this band and MM would show
a '(null)' info in the "Bands" area.
Band info as below:
n67, 738MHz-758MHz, SDL
Signed-off-by: Slark Xiao <slark_xiao@163.com>
With the FDO CI templates, the first container used must
be .fdo.container-build@ubuntu which builds the actual
container the rest of the pipeline can use with
.fdo.distribution-image@ubuntu.
.fdo.container-build@ubuntu uses a static 'image:' tag for
its job base image and then pushes to the project registry.
If the first job incorrectly uses .fdo.distribution-image@ubuntu
instead, it appears to fail for MR branches because that target
uses CI_REGISTRY_USER as part of the 'image:' tag which gitlab
sets to the username of the submitter. Which of course fails
because that user has never built the image before...
Using Docker executor with image registry.freedesktop.org/<username>/modemmanager/ubuntu/20.04:2023-01-03.1 ...
Authenticating with credentials from job payload (GitLab Registry)
Pulling docker image registry.freedesktop.org/<username>/modemmanager/ubuntu/20.04:2023-01-03.1 ...
Signed-off-by: Dan Williams <dan@ioncontrol.co>
Allows setting the renamed `ID_MM_QUALCOMM_FIREHOSE` and
`ID_MM_QUALCOMM_SAHARA` environment variables for all devices.
Signed-off-by: Lukas Voegl <lvoegl@tdt.de>
Add subsystem device ID support, that can be used in pci devices
instead of vendor/device ID customization.
Signed-off-by: Sushrut Shree Trivedi <quic_sushruts@quicinc.com>
The quectel modems that are not using QMI could receive DTMF events but
no dbus notification was sent to the user space. This patch adds the
DTMF notification support to the quectel plugin.
Signed-off-by: Kévin L'hôpital <kevin.lhopital@savoirfairelinux.com>
Since we're also now reading responses we need to check sender
credentials to make sure we're talking to the kernel, and not
some other process spoofing netlink.
Signed-off-by: Dan Williams <dan@ioncontrol.co>
Dan Williams
Guido Günther
Anagh G
Robert Marko
Dan Williams
Slark Xiao
Akula Susmitha
Sushrut Shree Trivedi
Michał Sułek
Evangelos Ribeiro Tzaras
Aleksander Morgado
Lukas Voegl
Kévin L'hôpital
Aleksander Morgado