When a nexthop is removed, routes depend on the removed nexthop are
already removed. It is not necessary to remove them, as already
commented. Let's forget them without trying to remove.
Previously, even if KeepConfiguration=dhcp or yes is specified in the
new .network file, dynamic configurations like DHCP address and routes
were dropped when 'networkctl reconfigure INTERFACE' is invoked.
If the setting is specified, let's gracefully handle the dynamic
configurations. Then, 'networkctl reconfigure' can be also used for
an interface that has critical connections.
Follow-up for dd6d53a8dc.
Unnecessary static configs will be anyway dropped later in
link_configure() -> link_drop_unmanaged_config(). Hence, even if we are
reconfiguring an interface cleanly, it is not necessary to drop static
configs here.
Unreachable routes are not owned by any interfaces, and its ifindex is
zero. Previously, if a non-upstream interface is reconfigured, all routes
including unreachable routes configured by the upstream interface are
removed.
This makes unreachable routes are always handled by the upstream interface,
and only removed when the delegated prefixes are changed or lost.
Follow-up for 451c2baf30.
With the commits, reloading .network files does not release previously
acquired DHCP lease and friends if possible.
On graceful reconfigure triggered by the reload, the interface may
acquire a new DHCPv4 lease earlier than DHCPv6 lease. In that case,
the check will fail as it is done with the new DHCPv4 lease and old
DHCPv6 lease, which does not contain any IPv6 DNS servers or so.
So, when switching from no -> yes, we need to wait a new lease with DNS
servers or so. To achieve that, we need to clean reconfigure the interface.
Follow-up for 451c2baf30.
With the commits, reloading .network files does not release previously
acquired DHCP lease and friends if possible. If previously a DHCP client
was configured as not requesting DNS servers or so, then the previously
acquired lease might not contain any DNS servers. In that case, if the
new .network file enables UseDNS=, then the interface should enter the
configured state after a new lease is acquired. To achieve that, we need
to reset the flags.
With this change, the workaround applied to the test by the commit
451c2baf30 can be dropped.
Otherwise, even if a link enters the configuring state at the beginning
of link_configure(), link_check_ready() may be called before
link_drop_unmanaged_config() is called, and the link may enter the
configured state.
Fixes#35092.
`loginctl kill-session --kill-whom=leader <N>` (or the D-Bus equivalent)
doesn't work because logind ends up calling `KillUnit(..., "main", ...)`
on a scope unit and these don't have a `MainPID` property. Here, I just
make it send a signal to the `Leader` directly.
Fixes a couple of bugs with systemd-sysupdated's target enumeration. See
commit messages for details.
<!-- devel-freezer =
{"comment-id":"2460494553","freezing-tag":"v257-rc1"} -->
To keep align with the logic used in udev_rules_parse_file(), we also
should skip the empty udev rules file while collecting the stats during
manager reload. Otherwise all udev rules files will be parsed again whenever
reloading udev manager with an empty udev rules file. It's time consuming
and the following uevents will fail with timeout.
A bit confusingly CONTAINER_UID_BASE_MAX is just the maximum *base* UID
for a container. Thus, with the usual 64K UID assignments, the last
actual container UID is CONTAINER_UID_BASE_MAX+0xFFFF.
To make this less confusing define CONTAINER_UID_MIN/MAX that add the
missing extra space.
Also adjust two uses where this was mishandled so far, due to this
confusion.
With this change the UID ranges we default to should properly match what
is documented on https://systemd.io/UIDS-GIDS/.
In the troff output, this doesn't seem to make any difference. But in the
html output, the whitespace is sometimes preserved, creating an additional
gap before the following content. Drop it everywhere to avoid this.
This allows loading the X.509 certificate from an OpenSSL provider
instead of a file system path. This allows loading certficates directly
from hardware tokens instead of having to export them to a file on
disk first.
<!-- devel-freezer =
{"comment-id":"2460915782","freezing-tag":"v257-rc1"} -->
This verb writes a public key to stdout extracted from either a public key
path, from a certificate (path or provider) or from a private key (path,
engine, provider). We'll use this in ukify to get rid of the use of the
python cryptography module to convert a private key or certificate to a
public key.
This allows loading the X.509 certificate from an OpenSSL provider
instead of a file system path. This allows loading certficates directly
from hardware tokens instead of having to export them to a file on
disk first.
Yu Watanabe
Luca Boccassi
Gabriel Elyas
Zbigniew Jędrzejewski-Szmek
12paper
Valentin David
Weblate Translation Memory
Ettore Atalan
Mike Yuan
Lidong Zhong
Lennart Poettering
Franck Bui
Ryan Wilson
anonymix007
Daan De Meyer
Vursc