TPM 1.2 is obsolete, and doesn't really provide much security guarantees
given it's build around SHA1 which is not up to today's standards.
The rest of systemd's TPM codebase never supported TPM 1.2 hence let's
drop this partial support in sd-stub too. It has created problems after
all (sd-stub reported the measuements and userspace assumed these were
for TPM2), without bringing any benefits (given that the measurements we
make are not consumed by us anyway, unlike those for TPM 2.0)
let's cut off this old support.
Add persistent symlinks for media controller ("mediaX") devices, based
on their ID_PATH udev properties.
For example, if the uvcvideo driver creates /dev/media0, a persistent
name may be:
/dev/media/by-path/pci-0000:04:00.3-usb-0:1:1.0-media-controller
Persistent links are a handy tool to make scripts self-documenting
during development or in tests, as well as less error prone in case of
devices changing enumeration order. For media controllers, one can
alternatively scan through all of them and look for a matching bus_info
in their struct media_device_info, but the links are much handier when
drafting something by hand.
A similar pattern already exists for Video4Linux /dev/videoX devices,
see 60-persistent-v4l.rules for those.
This deprecates IPForward= setting, which unconditionally controled
the global setting, even though it is a setting in .network file.
Instead, this introduces new IPv4Forwarding= and IPv6Forwarding=
settings both in .network and networkd.conf.
If these settings are specified in a .network file, then the
per-interface forwarding setting will be configured.
If specified in networkd.conf, then the global IP forwarding setting will
be configured.
Closes#30648.
I have a large initrd (built with mkosi-initrd) and the test-ukify takes 30 s.
Let's use the usual approach of skipping the slowests tests.
(pytest has marks, and it would be nicer to mark tests with pytest.mark.slow,
and then use "-m 'not slow'" in the meson test invocation. But markers must be
pre-registered, otherwise pytest emits a warning. There are a few ways to
register markers, but they all require "project configuration", but because of
how we invoke pytest, this is hard to do. So let's just use an environment
variable.)
Allow to set the broadcast queueing threshold
on macvlan devices. This controls which multicast packets will be
processed in a workqueue instead of inline.
The Xbox Wireless Headset does not get assigned a sound form factor
when connected via the dongle using the `xone` driver.
Add USB IDs for the old & new dongle and built-in variants.
Since we use varargs for sd_message_append() we need to make sure the
parameters we pass are actually 64bit wide, if "t" is used. Hence cast
appropriately if necessary.
I went through the whole tree, and in most cases we got it right, but
there are some cases we missed so far.
Inspired by: #31420
This renames a few of the switches vmspawn takes, such as --qemu-mem=
and --qemu-smp= to names without the "qemu" moniker and uses less
cryptic names (i.e. --ram= and --cpus=).
I think it's a bit unsystematic that so far we use the "qemu" prefix for
some options but not for others. At least I could not figure out a
system when we use it and when we don't. Hence let's clean it up and
just use simpler names without suffix.
After all we might want to plug other hypervisors behind vmspawn one
day, hence I think there's value in sticking to generic names for these
switches that allow us to switch out backends easily. In particular for
--ram= and --cpus= which are probably the most fundamental of VM settings
there are.
The old switches are support for compat, but not advertised in man page
or --help text anymore.
I left "--qemu-gui" under its current name, since it fundamentally is a
a qemu concept, exposing a qemu specific graphical UI.
The 1-based VT indexes are what people usually expect, since the primary
name of VTs uses them (i.e. /dev/tty1, /dev/tty2, …). Hence, let's
always use 1-based VT indexes, and early on convert 0-based VT indexes
to minimize confusion.
If specified we'll not try to find a free V, but instead just output
directly to the specified TTY. This is particularly useful for
debugging, as it means "systemd-bsod --tty=/dev/tty" just works.
Lennart Poettering
Yu Watanabe
Jan Macku
Max Staudt
zzywysm
Luca Boccassi
Zbigniew Jędrzejewski-Szmek
hulkoba
Mariano Giménez
Susant Sahani
Mike Yuan
medusalix
Frantisek Sumsal