If a crash occurs during an offline update, we do not get a
coredump, because systemd-coredump is not enabled. This of course
complicates debugging.
Signed-off-by: Adam Williamson <awilliam@redhat.com>
MultiPathRoute= can now specify device-only nexthops without a gateway
address, e.g. MultiPathRoute=@wg0. This enables ECMP configurations over
interfaces that don't use gateway addresses, such as WireGuard tunnels.
The syntax is extended from "address[@device] [weight]" to
"[address]@device [weight]". The address is now optional, but at least
one of gateway or device must be specified. The @ symbol must still be
present for device-only routes, making the syntax unambiguous: @wg0
specifies a device, while a bare IP address specifies a gateway.
Device-only nexthops are only available for IPv4 routes. Device-only
multipath routes for IPv6 are not supported by the kernel's netlink
interface and will be rejected with a warning.
This change is fully backwards compatible. All existing configurations
continue to work unchanged, as they always included a gateway address.
Closes#39699.
The UX of registering with the user session machined
instance is much better as there won't be an authorization
prompt. To make that available for users, let's add --user
and --system switches for vmspawn. For backwards compat, we'll
still try to register with the system machined instance if the
user machined instance is not available.
Follow-up for 179dcf924f
After the mentioned commit, event_add_child_pidref() duplicates
the pidfd internally, hence the original pidfd would be leaked
with TAKE_PIDREF.
To avoid the argument accidentally not getting passed anymore during
refactoring, let's make it a required output argument so that callers
are required to provide it.
See 11f47cb700 and
875b568f56.
Follow-up for 1684c56f40
This effectively reverts fd63e712b2
This was originally introduced to resolve deadlock caused by
dbus broker calling into nss-systemd which in turn goes via
dbus for user lookup. This is now handled differently and
the interface has been sitting unused for half a decade now.
Kill it.
Let's introduce these for the following two reasons:
- Using them makes sure the parameter names match between declaration
and definition (if both use the corresponding macros).
- They make sure developers can't forget the _const_ and _pure_
attributes for the declarations.
This commit also includes some include sorting fixes
When testing to correct accelerometer values I set locally the identity
matrix to override the quirk. The values were fine but removing all the
matrices give incorrect values.
The mistake was thinking that identity matrix is the default one when no
quirks are set. It is, but only when the ACPI doesn't have another one.
Set identity matrix for this device to correct accelerometer values.
Follow-up for a07b184e8c.
The current MAX_SERIAL_LEN value of 256 is insufficient for some SCSI
devices with non-standard serial number lengths. In do_scsi_page80_inquiry(),
the required buffer length is calculated as:
len = 1 + VENDOR_LENGTH + MODEL_LENGTH + buf[3]
= 1 + 8 + 16 + buf[3]
= 25 + buf[3]
where buf[3] contains the serial number length reported by the device.
According to the SCSI specification, this field is an unsigned 8-bit
value, meaning it can theoretically be up to 255 bytes. This results
in a maximum required length of 280 bytes, exceeding the current limit
of 256 bytes.
When this occurs, scsi_id fails with an error message like:
"length 256 too short - need 280"
This has been observed with certain vendor devices that report unusually
long serial numbers in VPD page 0x80.
Increase MAX_SERIAL_LEN to 512 to accommodate the maximum possible
serial number length plus all required prefixes (vendor, model, and
type identifiers), providing sufficient headroom for non-compliant
devices while maintaining reasonable memory usage.
Signed-off-by: tuhaowen <tuhaowen@uniontech.com>
Currently, the Bash completions for journalctl tries to match the
previous word _**exactly**_, which leads to the following issue:
`journalctl -u dock` correctly auto completes to `journalctl -u
docker.service`, but `journalctl -eu` provides no completions at all,
which is a shame since I never use the `-u` option alone (almost always
`-eu` or `-efu`, I wish the `-e` option was the default but I digress).
The proposed solution is to assume words that start with only a single
dash and consist of only letters are short option groups and handle them
as if the previous word was the short option using the last character,
e.g. `-efu` -> `-u`.
Follow-up for c1c787651b
The commit added serialization, but deserialization wasn't in place.
Follow the usual practice of pinning the bpf link fd until we install
the new instance.
* e3642f81d3 kmod: Only use --modname if available
* ddea81d81e arch: Download archlinux-keyring with pacman
* 4a44e1831b Remove unneeded lambdas
* 9c3d23757c Configure pyright included files
* 5e037d514c qemu: Register with systemd-machined in user session
* c4c3d793d0 Create package cache dir before invoking pacman
* d53761c4dd distribution: do not default to release=VERSION_ID for openSUSE Tumbleweed
* c5bc9138fc Wrap build_microcode_initrd in complete_step
* 635159975d Fix typo in manpage
* 59f5f0741e mkosi-addon: drop Output=addon, addon.py already has a default
* be85b8ca0b sandbox: return raw error code from the kernel and friends on failure
* 56f25c1a41 config: replace deprecated sandbox verb with box in help message
* ae24c527d7 sandbox: fix wrong errno passed to OSError()
* e7b9612760 verity: do not copy signing cert in addons/portables/extensions
* f3a029b736 Bump version to 27~devel
* 84af20892b Release 26
* 3fcd3a0fde Adjust logging messages for kmod/fw resolution
* d44aae12b4 Revert "Do not try to install packages that are listed in RemovePackages="
* 1873ad0184 portable: Make sure mountpoints exist in the image
* 5dc693feb0 initrd: Inherit keymap, timezone, hostname and rootpw by default
There are multiple ways to encode ANSI ST, and we generally prefer ESC \
for it, for reasons explained in terminal-util.h. Hence, let's actually
follow this rule in the terminal reset logic, and use the ANSI_ST macro.
This will change the byte sequence generated (as it means we use ESC \
rather than BEL), but it doesn't change behaviour, as the two sequences
should be equivalent.
Follow-up for 3d97db8f3c
terminal_reset_ansi_req() would try to put terminal in nonblocking
mode temporarily again, hence just avoid the back and forth
and reset nonblocking as last step.
Yu Watanabe
Adam Williamson
Daan De Meyer
Mike Yuan
David Santamaría Rogado
tuhaowen
dependabot[bot]
Ben Boeckel
Guiorgy
kiamvdd
smosia
Zongyuan He
Tobias Stoeckmann
Luca Boccassi
Lennart Poettering
Jörg Behrmann
Luiz Amaral